TOP PAGE > Product Information > Brands > Iupital > POM

Iupital-POM-

  Standard -2
Properties Test Method Terms Units F20-54
Weather
Resistance
Improved
General
-
Physical properties 
DensityISO 1183-g/cm31.41
Water absorption-23degC, 60%RH%0.22
Rheological properties 
Melt Mass-flow RateISO 1133 g/10min9.0
Melt Volume-flow Rate cm3/10min7.7
TemperaturedegC190
Loadkg2.16
Moulding shrinkage (3mmt)-MD%2.0
TD-
Mechanical properties 
Tensile modulusISO 527-1
, 527-2
-MPa2800
Yield stress62
Yield strain%8.5
Nominal strain at break30
Stress at breakMPa-
Strain at break%-
Flexural strengthISO 178-MPa88
Flexural modulus2500
Charpy impact strengthISO 179-1, 179-223 degCkJ/m2240
Charpy notched impact strengthISO 179-1, 179-223 degCkJ/m26.5
Thermal properties 
Melting temperatureISO 11357-3 degC166
Temperature of deflection under loadISO 75-1
, 75-2
1.80MPadegC100
0.45MPa156
Coefficient of Linear thermal expansionISO 11359-2MD1/degC1.1E-04
TD1.1E-04
FlammabilityUL940.8mmt-HB
Electrical properties 
Relative permittivityIEC 60250100Hz--
1MHz--
Dissipation factorIEC 60250100Hz--
1MHz--
Volume resistivityIEC 60093-ohm-m1E+12
Surface resistivityIEC 60093-ohm1E+16
Electric strengthIEC 60243-11mmtMV/m-
3mmt -
Comparative tracking indexIEC 60112---
Note    
Molding conditions -Examples of recommended molding conditions are shown below.- 
Drying of feedstock resin   Hot air drying
at 80℃---about 3-4 hours     
Cylinder temp (rear)  170
Cylinder temp (center)  180
Cylinder temp (front)  190
Nozzle temp  180-210
Mold temp  60-80
Injection pressure  MPa50-100
Screw rotation   rpm80-120
Injection speed  -middle

Note

  • The values described are typical values only.
  • The usage examples indicated here do not guarantee results applicable to relevant uses of the products.
  • It is the users' responsibility to investigate industrial property rights and the terms of use related to the uses and applications indicated here.
  • For the handling (transport, storage, forming, disposal, etc.) of the products, it is advisable to refer to technical documents and the Safety Data Sheet (SDS) of the proper materials and grades. Please contact us for consultations when the products are used for the purpose of food containers and packaging, medical parts, safety equipment, and toys for children.
  • In Japan, the colored products of each grade may contain chemicals subject to reporting requirements under the applicable law provided in Appendix 9 of Article 18-2 of the Enforcement Order, under Article 57-2 of the Industrial Safety and Health Act. For details, please contact us.
  • For the export of our products and products incorporated with our products, please comply with the relevant laws and regulations, such as the Foreign Exchange and Foreign Trade Law.
  • Please note that because of the chemical substance management systems in each country, the chemicals used in our products are subject to control, and separate applications might be required or are banned from imports and exports. It is advisable to inquire about the status of regulations in the relevant countries if you are exporting or importing our products.

Product Info.

  • ポリカーボネート樹脂(PC樹脂)ユーピロンノバレックスザンター
  • ポリブチレン テレフタレート樹脂 (PBT樹脂) ノバデュラン
  • ポリアセタール樹脂(POM樹脂)ユピタール
  • 変性ポリフェニレン エーテル樹脂(m-PPE樹脂)ユピエースレマロイ
  • 高性能ポリアミド樹脂(PA樹脂)レニー
Basic Properties
PDFdownload
Applications
SDS Inquiry

PAGE TOP

Are you direct sales contacts of MEP materials ?

We kindly ask you to request in accordance with your sales channels